Description
Description:
If you are wandering to navigate the distance with a drone then this NEO 7M GPS Module is needed. GPS drones are equipped with a NEO 7M GPS Module that lets them know their location relative to a network of satellites. Connecting to signals from these satellites allows the drone to perform functions such as position hold, autonomous flight, return to home, and waypoint navigation.
NEO 7M GPS Module that includes an HMC5883L digital compass. The new NEO 7 series is a high-sensitivity, low-power GPS module with 56 channels and outputs precise position updates at 10Hz. This NEO 7M GPS Module also comes with a molded plastic case which keeps the module protected against the elements making it ideal for use on your aircraft or quadcopter.
This NEO 7M GPS Module uses an active circuitry ceramic patch antenna to provide an excellent GPS signal which outperforms the older Neo 6 series modules. This NEO 7M GPS Module also includes a rechargeable backup battery to allow for HOT starts and also includes an I²C EEPROM to store the configuration settings.  Out of the box, this NEO 7M GPS Module is configured to run at 38400 Baud and is configured to run with APM/Pixhawk systems.  This NEO 7M GPS Module includes two cables, a 6-pin connector for the GPS module, and a 4-pin connector for the i2c compass.
Specifications:
- Model: NEO 7M
- Receiver Type:Â 56 Channels, Galileo E1B/C1, GPS L1C/A, QZSS L1C/A, SBAS L1C/A
- Receiver Frequency:Â L1 [1575.42MHz]
- Input Supply Voltage: 3.5 ~ 5.5V DC
- Main Chip:Â U-BLOX NEO-7M
- Sensitivity (dBm):Â -155, -160, Cold Start (without aiding): -147 dBm, Tracking & Navigation: -161 dBm
- Position Accuracy: 2, 2.5Meter
- Acceleration: <4g
- Navigation Update Rate:Â 5Hz
- Operating Temperature Range: -24 to 84°C
- Tracking Sensitivity: -161 DBM
- Co-Ordinate System:Â WGS-84
- Capture Time:Â 0.1s Average
- Avg Cold Start Time:Â 38s
- Warm Start Time: 35s
- Boot Time:Â 1S
- Maximum Altitude:Â 18000m
- Maximum Speed:Â 515 m/s
Features:
- Locate performance
- Super Bright LED
- compass on board
- 4-pin connector for only GPS use
- 1Hz (Default) Changed to 5Hz!
- Permanent Configuration Retention
- Output GGA, GSA, and RMC frames
- 38400 bps (Default) Changed to 115200bps!
- 4-pin connector for compass only use
- The 6-pin connector for EZ connects to MEGA BLACK
- NEO 7M GPS Module can use both 4 pins at once.
- Backplane with Standard Mk style mounting holes 45mm X 45mm
- These are Pre-configured, Flashed with the correct settings, and tested. To make them Plug and Play.
Package Included:
1 x NEO 7M GPS Module NEO 7M GPS With Compass for APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8








L298N Based Dual Motor Driver Speed And Direction Control Raspberry Pi-Controlled Dual Motor Driver Motor Driver Circuit Build Your Own Robot
5400mAh Lipo Battery 14.8V 5400mAh 4S 30C Lithium Polymer Battery
EMAX Bullet Series 35A ESC (BLHELI_S) with Oneshot (Original)
Raspberry Pi Pico H RP2040 Microcontroller Chip Development Board
Female Deans T-Plug Connector Deans Connector For RC LiPo Battery T-Plug Connector For ESC High-Quality Deans Connector For RC Applications
UW 01 Washing/Curing Machine
Daisy White PLA PRO+
Raspberry Pi Bumper for Raspberry Pi 5 Shock-Absorbing Case for Pi 5 Protective Bumper Case for Pi 5 Raspberry Pi 5 Bumper Case
20A Brushed ESC 20A Brushed Electronic Speed Controller w/Brake For RC Car Boat Tank
40A ESC Brushless Speed Controller ESC For Quadcopter Brushless Motor Speed Controller With BEC ESC 40A For RC Car High-performance ESC 40A With Thermal Protection
220 Ohm Resistor, 220 Ohm Resistance 1/4W Power Rating 5%
FS-SM100 USB Simulator Cable with Adapter Cables for Flysky FS-i6 FS-i4 FS-TH9X FS-T6 FS-T4B FS-GT3 FS-GT2 Remote Controller
Raspberry Pi Compute Module 4 - CM4102008- 2GB RAM - 8GB eMMC - Wireless
3M 20mm Double Sided Adhesive Pad Dia Multipurpose Double Sided Sponge Glue Adhesive Dash Pad For GPS - 4Pcs
Candy Red PLA PRO+
Raspberry Pi 4 Model-B 2GB SDRAM Raspberry PI 4B SBC IOT Board - Broadcom 1.5GHZ A72 Processor
15-22 Inch Propeller Adapter Quick Release Prop Adapter CW&CCW For 15-22 Inch Prop / M3 15mm Hole Motor (Without Mounting Plate)
Bambu Lab X1 – Carbon Combo 3D Printer
Reviews
There are no reviews yet.