Description
Description:
The NE555 Timer IC is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the time delay mode of operation, the time is precisely controlled by one external resistor and capacitor. For astable operation as an oscillator, the free running frequency and duty cycle are accurately controlled with two external resistors and one capacitor. The NE555 Timer IC may be triggered and reset on falling waveforms, and the output circuit can source or sink up to 200mA or drive TTL circuits.
Specifications:
- Package/Case: DIP-8
- Minimum Supply Voltage: 4.5V
- Maximum Supply Voltage: 16V
- Product Series: NE555
- No. of Timers/Counters: 1
- Operating Temperature Range: 0 ~ 70°C
Features:
- Timing from microseconds through hours
- NE555 Timer IC operates in both astable and monostable modes
- NE555 Timer IC has adjustable duty cycle
- Output can source or sink 200 mA
- Output and supply TTL compatible
- NE555 Timer IC has normally on and normally off output
- NE555 Timer IC is available in 8-pin MSOP package
Pin Description:
| Pin | Name | Purpose |
| 1 | GND | Ground reference voltage, low level (0 V) |
| 2 | TRIG | The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. The output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin. |
| 3 | OUT | This output is driven to approximately 1.7 V below +Vcc, or to GND. |
| 4 | RESET | A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold. |
| 5 | CTRL | Provides “control” access to the internal voltage divider (by default, 2/3 Vcc). |
| 6 | THR | The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open). |
| 7 | DIS | Open collector output which may discharge a capacitor between intervals. In phase with output. |
| 8 | VCC | Positive supply voltage, which is usually between 3 and 15 V depending on the variation. |
Package Included:
1 x NE555 Timer IC 555 DIP-8 General Purpose Single Bipolar Timer IC
Waveshare 15.6" Full HD IPS Monitor 100% sRGB Color Accuracy, 1920x1080 IPS Display, Slim Profile With Adjustable Stand For Stunning Clarity 
L293D Motor Driver IC PowerDIP-16 Stepper Motor Controller/ Driver IC 
DC Barrel Power Jack/Connector 
DPDT Switch Push to ON OFF Horizontal Switch 
100RPM DC BO Motor singal Shaft Smart Car Robot Gear Motor 
12V 200 RPM Geared Motor Johnson DC Gearbox Motor High-Torque 200 RPM Geared Motor High-Performance 100 RPM DC Geared Motor 
3S 60A Li-ion BMS Board 18650 Battery Charger Protection Circuit 3S 60A BMS For Li-ion Batteries Three-Cell Li-ion Battery Protection Module - Standard Version 
Raspberry Pi 4 TFT 3.5 inch Touch Screen with Case, 480x320 Resolution 60fps Monitor LCD Display 
4-Pin 30A Rocker Switch 250V 12V Illuminated Rocker Switch UL Illuminated Rocker Switch Brighten Up Your Projects With Illuminated Rocker Switch 
30 Type Assorted Resistor Kit 600 pcs 
Tactile Switch Small Mini Micro Tactile Push Button 
A4988 Stepper Motor Driver 3D Printer Reprap Stepper Driver A4988 Motor Driver Module With Heat Sinks For Arduino And Raspberry Pi 
5MP Raspberry Pi Camera 1080p Adjustable Focus Camera OV5647 Focus Camera Raspberry Pi Camera Module Raspberry Pi 3/2 Model B/B+ 
Generic Micro Endstop Switch Micro Switch Mechanical End Stop AC 250V 5A SPDT Miniature NO/NC Switch For Reprap 3D Printer/CNC/DIY 
Push Button 12x12x7.3mm Tactile 4 Pin Push Button Switch 
12V 500RPM Gear Motor Centre Shaft DC Geared Motor Heavy Duty Motor for Robotics 
SM 2 Pin Plug Male Connector Adapter with 150 mm Electrical Cable Wire for LED Light 
65-Pieces T-Tap Wire Connector Kit Insulated Wire Connector 22-18, 18-14, 12-10 AWG Assortment Kit For Fast & Reliable Wiring 
5x6 18650 Battery Spacer Holder With 18.5mm Bore Battery Holder Lithium-ion Battery Holder Rechargeable Battery Holder Plastic Holder For DIY Battery Pack 
CD4504 IC Hex Voltage Level Shifter IC DIP-16 Package 
3PI miniQ Car wheel Tyre 42mm N20 DC Gear Motor Wheel 
CR 10 SE 3D Printer 
Arduino Uno Prototype Shield Protoshield Expansion Board Module With Mini Breadboard Compatible With Arduino 
Official Raspberry Pi 5 Case Red and White Raspberry Pi 5 ABS Case Raspberry Pi 5 Active Cooling PWM Fan Protection 
Nextion NX8048T050 5.0" HMI Touch Display 5-inch Basic Series Display Touchscreen Display for Arduino Raspberry Pi 
4 USB Fast Charging Module Board 12V24V to QC2.0 QC3.0 Step Down Power Supply Module 12V 24V 
Radiolink Cool 9030 ESC 90A Brushed (2-4S) Waterproof Built-in BEC 5A Selectable 5.5V/7.5V for RC Truck Crawlers Tanks Cars Bait Boats (XT60 Plug) 
Raspberry Pi 4 Official Case for Raspberry PI 4 Model B 1GB, 2GB, 4GB, 8GB - (RED/White) 
No Touch Stainless Steel Door Exit Switch/Touch Free Exit Push Release Button Switch for Electric Access Control 
Arducam M12 Lens Board Precision Focus and Angle Enhancement M12 Adjustable Lens Board For Raspberry Pi 4/3/3 B+ Camera 
Raspberry Pi 4B Camera IR Camera Module With Holder and Cable IR Camera Module 75 Degree 5MP OV5647 Webcam Automatically Switching Between Day Vision and Night Visio For Raspberry Pi 4B 3B+ 2B+ Zero and Zero W 
iMAX B6AC Charger iMAX B6 LCD Screen Digital RC Lipo NiMh Battery Balance Charger B6AC Lipo Charging XT60/T Plug Adaptor Board 2-6S
Reviews
There are no reviews yet.